Can I Install A Bath Tub Myself?
Can I Install A Bath Tub Myself?
Blog Article
We have stumbled on this article about How to Install a Bathtub directly below on the internet and thought it made perfect sense to discuss it with you here.
Installing a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily accessible, the task can relocate rapidly; if you need to open up a wall to remove the old bathtub and place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will require a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Opportunities are you may require an expert plumber to make tube links.
This post will assist you install a brand-new bathtub in your washroom if you have already bought a brand-new tub and do not need to change the plan of your previous supply of water pipelines.
Your tools and product checklist need to make up the following:
Getting ready for the Installment
First of all, the sustaining framework provided with the bath should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the versatile faucet ports to the bottom of both taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its last placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be rather bothersome as a result of the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has actually been used a minimum of once as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind should be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in usage. The sealer can fracture fairly early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on How to Install a Bathtub. Thanks a ton for taking a few minutes to read our article. Loved our entry? Please share it. Help others discover it. Thank you for your time invested reading it.
Book Your Appointment
Report this page